進口可調式氣體減壓閥（德國OLES奧萊斯閥門）

【進口可調式氣體減壓閥】詳細說明：

減壓閥適用于蒸汽、空氣介質管路上，使用于氧氣、空氣介質管路上。法蘭先導活塞式蒸汽減壓閥是通過調節將使進口壓力降低至某一需要的出口壓力，當進口壓力與流量有變化時，靠截肢本身能量可自動保持出口壓力在一定范圍內但進口壓力和出口壓力之差必須≥0.2MPa/cm2。氣體減壓閥主要用于氣體管路，同樣適用于如空氣、氮氣、氧氣、氫氣、煤氣、液化氣、天然氣等氣體。空氣減壓閥屬于先導活塞式減壓閥。由主閥和導閥兩部分組成。主閥主要由閥座、主閥盤、活塞、彈簧等零件組成。導閥主要由閥座、閥瓣、膜片、彈簧、調節彈簧等零件組成。通過調節調節彈簧壓力設定出口壓力、利用膜片傳感出口壓力變化，通過導閥啟閉驅動活塞調節主閥節流部位過流面積的大小，實現減壓穩壓功能。

Pressure relief valves are suitable for steam and air medium pipelines, and for oxygen and air medium pipelines. Flange pilot piston steam pressure relief valve reduces the inlet pressure to a required outlet pressure by regulating. When the inlet pressure and flow rate change, the outlet pressure can be automatically maintained within a certain range by the energy of amputation itself, but the difference between the inlet pressure and the outlet pressure must be more than 0.2 MPa/cm2. Gas pressure relief valves are mainly used in gas pipelines, as well as in air, nitrogen, oxygen, hydrogen, gas, liquefied gas, natural gas and other gases. The air pressure reducing valve belongs to the pilot piston type pressure reducing valve. It consists of main valve and pilot valve. The main valve is mainly composed of seat, main disc, piston, spring and other parts. The guide valve is mainly composed of seat, disc, diaphragm, spring, adjusting spring and other parts. The outlet pressure is set by adjusting the spring pressure, the diaphragm is used to sense the outlet pressure change, and the pilot valve opens and closes to drive the piston to adjust the flow area of the throttle part of the main valve, so as to realize the function of reducing pressure and stabilizing pressure.

【進口可調式氣體減壓閥】安裝注意事項：

1.為了操作和維護方便，該蒸汽減壓閥一般直立安裝在水平管道上，橫向安裝須特別說明。

2.安裝時應注意使管路中介質的流向與蒸汽減壓閥閥體上所示箭頭的方向*。

3.為了防止蒸汽減壓閥閥后壓力超壓，應在離閥出口不少于4M處安裝一個安全閥

空氣減壓閥可能的故障原因：

1、霜凍損壞，在寒冷地區應注意保溫。

2、水流方向裝錯，減壓閥變成止回閥，出口壓力為0。

3、彈簧擰得太緊，無法關閉，減壓閥將直通P2=P1。

4、旁通管漏水，使P2偏離設定值，鑒于本減壓閥*的可靠性和耐久性，建議不安裝亮度通管為宜。

【進口可調式氣體減壓閥】調壓步驟：

1、關閉減壓閥前的閘閥，開啟減壓閥后的閘閥，制造下游低壓環境；將調節螺釘按逆時針旋轉*位置（相對低出口壓力），然后關閉減壓閥后閘閥。

2、慢慢開啟減壓閥前的閘閥至全開。

3、順時針慢慢旋轉調節螺釘，將出口壓力調至所需要的壓力（以閥后表壓為準）；調整好后，將鎖緊。

4、螺母鎖緊打開減壓閥后閘閥。

5、如在調整時出口壓力高于設定壓力，須從*步開始重新調整，即只能從低壓向高壓調。